Hello Arrangereers,

I'm no expert with the MFC-10 but I do have some simplified instructions for setting it up to fade the R2 voice In & out, and to control the keyboard's vocal harmony (on/off) function. I don't know how many want this information but here it is:

Initial Preparation:

1) Turn ON the MFC10.

NOTE: Make sure that the 2 switches in the back are set to 'NORMAL' and 'MIDI'.

2) Connect a MIDI cable from the MFC10 'MIDI OUT' to the 9000PRO 'MIDI B IN'.

3) Connect a MIDI cable from the 9000PRO 'MIDI B OUT' to the MFC10 'MIDI IN'.

NOTE: Make sure that the 'HOST SELECT' switch in the back of the 9000PRO is set to 'MIDI'.

4) Turn ON the 9000PRO.

5) Press the [MIDI] button.

6) Press the button under 'MFC10' in the screen.


Full Setup (for creating customized Templates):

In the following example, a custom Template will be created from a preset one, using the MFC10 to control the Volume of the 9000PRO 'R2' section (set to Strings), and to turn Vocal Harmony ON/OFF.

1) Select 'Full Setup' in the screen.

2) Turn ON the [FUNCTION] button on the MFC10.

3) Press the [NEXT] button on the 9000PRO.

4) Press the [NEXT] button again.

5) Select a preset Template in the screen.

EXAMPLE: 'DSP CONTROL'.

6) Press the [NEXT] button.

7) Assign functions to the Foot Controllers in the screen.

EXAMPLE: Assign '1(INT.) VOLUME' to 'RIGHT 2'. (This allows the MFC10 on-board Foot Controller to control the Volume of the 9000PRO 'R2' section.)

8) Press the [NEXT] button.

9) Assign functions to the Foot Switches in the screen.

EXAMPLE: Switch 'F06' is already set up to control Vocal Harmony ON/OFF.

10) Press the [NEXT] button.

11) Select an empty Template location in the screen.

EXAMPLE: '05 :No Data'.

12) Press the [NEXT] button.

13) Name the custom Template.

14) When finished, press the button under 'END' in the screen.

15) Press the [G] button twice.

16) Unplug the MIDI cable from the 9000PRO 'MIDI B OUT' jack.

17) Press the [EXIT] button.

18) Select a desired Voice for the 'R1' section, and then the 'R2' section (select STRINGS).

The MFC10 Foot Controller wil now control the Volume of the 9000PRO 'R2' section (STRINGS). The MFC10 Foot Switch [6] will now toggle the 9000PRO Vocal Harmony function ON/OFF.


Backup the Template settings:

1) Press the [A] button.

2) Press the [G] button to backup the new settings.

9000PRO Owner's Manual, p. 178-179

Well, that's it. Hope it helps the MFC-10 owners out there.

Regards,
Steve

?

[This message has been edited by 9000 Robby (edited 07-13-2001).]

Robby,
Would be interesting if I could read it!
Nobby

?

[This message has been edited by 9000 Robby (edited 07-13-2001).]

Hallo Robby,
Ich glaube er meint das er kein deutsch Kann.
Gruss
Eric

?

[This message has been edited by 9000 Robby (edited 07-13-2001).]

OK, we've heard from Europe. Can anyone translate?

thanks,
Steve

Robby writes: Hi friends the guy in the picture is me. Sorry, that I can't speak english and you guys can't speak german.
Eric

I must say, Robby is very good at creating these active, animated message posts! Those bouncing smile faces and all - how DOES he do that? And his webpages look very full of info - like he put a lot of work into creating them. I just don't think I can translate them fast enough to look through everything.
Tom

?

[This message has been edited by 9000 Robby (edited 07-13-2001).]