![](http://www.synthzone.com/forum/styles/images/black_and_gold/top_left_1.gif) |
![](http://www.synthzone.com/forum/styles/images/black_and_gold/top_left_2.gif) |
![](http://www.synthzone.com/forum/styles/images/black_and_gold/top_span.gif) |
![](http://www.synthzone.com/forum/styles/images/black_and_gold/top_right_1.gif) |
![](http://www.synthzone.com/forum/styles/images/black_and_gold/top_right_2.gif) |
![](http://www.synthzone.com/forum/styles/images/black_and_gold/left_span.gif) |
#317884 - 02/28/11 06:40 PM
Labelling SD Cards
|
Member
Registered: 09/17/07
Posts: 93
Loc: Staffordshire, England
|
.
Good Morning Ivory Ticklers,
Its 2.30am and here I am still burning the midnight oil !!
I now have 8 (2Gb) SD Cards, between my Movie Camera and the KN7000, and will probably amass more !! In both uses, I need to label or mark them in some way to identify what is on them, (Styles, Backings, Recordings, etc..) on the KN7, and similar for the Movie Camera.
I toyed with the idea of cutting a small adhesive label and sticking it on, but would be in deep 'Doo Doo' if the label came off when inserting or removing it from the SD Slots.
How do you mark yours, please ?
Regards,
John
.
|
Top
|
|
|
|
|
![](http://www.synthzone.com/forum/styles/images/black_and_gold/right_span.gif) |
![](http://www.synthzone.com/forum/styles/images/black_and_gold/bottom_left_1.gif) |
![](http://www.synthzone.com/forum/styles/images/black_and_gold/bottom_left_2.gif) |
![](http://www.synthzone.com/forum/styles/images/black_and_gold/bottom_span.gif) |
![](http://www.synthzone.com/forum/styles/images/black_and_gold/bottom_right_1.gif) |
![](http://www.synthzone.com/forum/styles/images/black_and_gold/bottom_right_2.gif) |
![](http://www.synthzone.com/forum/styles/images/black_and_gold/top_left_1.gif) |
![](http://www.synthzone.com/forum/styles/images/black_and_gold/top_left_2.gif) |
![](http://www.synthzone.com/forum/styles/images/black_and_gold/top_span.gif) |
![](http://www.synthzone.com/forum/styles/images/black_and_gold/top_right_1.gif) |
![](http://www.synthzone.com/forum/styles/images/black_and_gold/top_right_2.gif) |
![](http://www.synthzone.com/forum/styles/images/black_and_gold/left_span.gif) |
#317899 - 02/28/11 10:55 PM
Re: Labelling SD Cards
[Re: Bob Hendershot]
|
Member
Registered: 09/17/07
Posts: 93
Loc: Staffordshire, England
|
. Thanks for the speedy response, Bob and Ray, I have followed your advice, and 'scissored' two floppy disk labels to a slightly smaller size than the SD Cards. Stuck them on, and just used two-letter 'Identifiers' .... 'ST1' = Styles Card 1, 'BA1' = Backing Trax 1, etc.. I found it easier to draw round the SD card with a pen, then write the title', before cutting them up, a tad smaller than the card. And as Bob suggests, stuck them on to the plastic, rather than over the existing brand labels. Better run off quickly to the bathroom, Ray - you look as if you are 'bursting' - LOL Cheers & Beers, John (Always fiddling with something !!) ![violin violin](/forum/images/graemlins/default_dark/violin.gif) .
|
Top
|
|
|
|
|
![](http://www.synthzone.com/forum/styles/images/black_and_gold/right_span.gif) |
![](http://www.synthzone.com/forum/styles/images/black_and_gold/bottom_left_1.gif) |
![](http://www.synthzone.com/forum/styles/images/black_and_gold/bottom_left_2.gif) |
![](http://www.synthzone.com/forum/styles/images/black_and_gold/bottom_span.gif) |
![](http://www.synthzone.com/forum/styles/images/black_and_gold/bottom_right_1.gif) |
![](http://www.synthzone.com/forum/styles/images/black_and_gold/bottom_right_2.gif) |
|
|