![](http://www.synthzone.com/forum/styles/images/black_and_gold/top_left_1.gif) |
![](http://www.synthzone.com/forum/styles/images/black_and_gold/top_left_2.gif) |
![](http://www.synthzone.com/forum/styles/images/black_and_gold/top_span.gif) |
![](http://www.synthzone.com/forum/styles/images/black_and_gold/top_right_1.gif) |
![](http://www.synthzone.com/forum/styles/images/black_and_gold/top_right_2.gif) |
![](http://www.synthzone.com/forum/styles/images/black_and_gold/left_span.gif) |
#51736 - 08/19/03 08:44 PM
Re: KN7000 Pads
|
Member
Registered: 01/16/02
Posts: 71
Loc: Calimesa, Ca, USA
|
Hi Keith and Rikki, I had the same problem back in 2001 and Alec Pagida graciously gave me the answer to store 3 different pads sets in loading the pads. For example: in User 1 - Big Band Slow, User 2 - Big Band Fast, User 3 - Big Band Swing. All in 1 load of the pads. You condense the pads as follows: (Alec's Instructions): SAVE YOUR CUSTOM SECTION IF IT IS NOT THE INITIAL.
1. load file 3 2. copy composer A to custom 3 3. load file 2 4. copy composer A to custom 2 5. load file 1 6. copy custom 2 to composer B (change direction in the screen). 7. copy custom 3 to composer C 8. save a new pad file only (page 2 all off, pads on.) now repeat the above steps for file 6, 5 and 4 in that order, then again for 9,8,7. This is used in condensing a pad disk with 10 files down to 4 files or you can pick out the pads in the 3 user banks that would go with one another. It seems around about way of doing it, but it worked for me and hopefully it will for you. Best Regards, Dave
|
Top
|
|
|
|
|
![](http://www.synthzone.com/forum/styles/images/black_and_gold/right_span.gif) |
![](http://www.synthzone.com/forum/styles/images/black_and_gold/bottom_left_1.gif) |
![](http://www.synthzone.com/forum/styles/images/black_and_gold/bottom_left_2.gif) |
![](http://www.synthzone.com/forum/styles/images/black_and_gold/bottom_span.gif) |
![](http://www.synthzone.com/forum/styles/images/black_and_gold/bottom_right_1.gif) |
![](http://www.synthzone.com/forum/styles/images/black_and_gold/bottom_right_2.gif) |
![](http://www.synthzone.com/forum/styles/images/black_and_gold/top_left_1.gif) |
![](http://www.synthzone.com/forum/styles/images/black_and_gold/top_left_2.gif) |
![](http://www.synthzone.com/forum/styles/images/black_and_gold/top_span.gif) |
![](http://www.synthzone.com/forum/styles/images/black_and_gold/top_right_1.gif) |
![](http://www.synthzone.com/forum/styles/images/black_and_gold/top_right_2.gif) |
![](http://www.synthzone.com/forum/styles/images/black_and_gold/left_span.gif) |
#51739 - 08/20/03 01:55 PM
Re: KN7000 Pads
|
Senior Member
Registered: 12/22/02
Posts: 6020
Loc: NSW,Australia
|
Thank you Dave, I'll give it a try. My solution was going to give me big headaches haahaa. best wishes Rikki Originally posted by Dave Shively: Hi Keith and Rikki, I had the same problem back in 2001 and Alec Pagida graciously gave me the answer to store 3 different pads sets in loading the pads. For example: in User 1 - Big Band Slow, User 2 - Big Band Fast, User 3 - Big Band Swing. All in 1 load of the pads. You condense the pads as follows: (Alec's Instructions): SAVE YOUR CUSTOM SECTION IF IT IS NOT THE INITIAL.
1. load file 3 2. copy composer A to custom 3 3. load file 2 4. copy composer A to custom 2 5. load file 1 6. copy custom 2 to composer B (change direction in the screen). 7. copy custom 3 to composer C 8. save a new pad file only (page 2 all off, pads on.) now repeat the above steps for file 6, 5 and 4 in that order, then again for 9,8,7. This is used in condensing a pad disk with 10 files down to 4 files or you can pick out the pads in the 3 user banks that would go with one another. It seems around about way of doing it, but it worked for me and hopefully it will for you. Best Regards, Dave
_________________________
best wishes Rikki 🧸
Korg PA5X 88 note SX900 Band in a Box 2022
|
Top
|
|
|
|
|
![](http://www.synthzone.com/forum/styles/images/black_and_gold/right_span.gif) |
![](http://www.synthzone.com/forum/styles/images/black_and_gold/bottom_left_1.gif) |
![](http://www.synthzone.com/forum/styles/images/black_and_gold/bottom_left_2.gif) |
![](http://www.synthzone.com/forum/styles/images/black_and_gold/bottom_span.gif) |
![](http://www.synthzone.com/forum/styles/images/black_and_gold/bottom_right_1.gif) |
![](http://www.synthzone.com/forum/styles/images/black_and_gold/bottom_right_2.gif) |
|
|